2 pieces: 16" x 14" Silver Steel Slip-Fit Bases with Base Pins (optional base edge protectors). 1 piece: Adjustable 6-10 Foot Width Silver Aluminum Drape Support Rod. What are Break Apart Uprights?Uprights set the height of your pipe and drape display, and are the vertical pieces of pipe that is located at each end of a horizontal drape support rod. Two pieces of pipe work together to make an 8 foot tall upright in this break apart system. A 4 foot section serves as the bottom of the upright and is put on the base, and a 4 foot 4 inch section serves as the top piece. The 4 portion, located at the bottom of the top pipe, has a slightly smaller diameter and simply slips inside of the top opening of the bottom piece, as shown in the listing photo. Having a break apart upright makes transportation much easier compared to a fixed (one piece) 8 foot Upright. This will fit in most vehicles, whereas an 8 foot fixed (non-break apart) pipe is will not fit inside of most cars (except for some large SUVs).
IMPORTANT: Because it consists of two pieces (rather than one solid piece like our fixed uprights), the break apart uprights have a bit more wiggle room compared to our fixed uprights. This degree of wiggle can be significantly minimized by ensuring that the spacing between your uprights and drape support rod is correct when setting up your display.The edges of these bases can be raw or rough. Edge protectors help protect your hands and the flooring. Size - 96"H x 1.5" diameter Weight - Approximately 2.1 lbs each Material - Aluminum Color - Silver Other - Break Apart Version. Four 90° slots are cut out at 36H and at the top. Size - 16" x 14" with stacking slot Weight.
Approximately 10 lbs each with included 3H steel base pin. Material - Steel Color - Silver Other - Edge protectors optional. Drape Support Rod (horizontal pipe). Size - 72"L at collapsed size, 120"L at fully extended size, 1.5 diameter Weight - Approximately 3.5 lbs. Weight capacity is 15 lbs.Material - Aluminum Color - Silver Other - Adjustable from 6 to 10 feet wide. Button stop at 8 and 10 foot intervals. What Is The Slip-Fit System?
The slip-fit system is designed to be a tremendous time saver for setting up and breaking down your pipe and drape display. The uprights are hollow, allowing them to simply slip over the base pin (included with each base).The drape support rod features steel hooks at each end that slip inside of one of the four slots cut out at the top of the upright. Estimated set-up time varies based on the number of people and the speed at which he or she works, but should average about 5-10 minutes once the boxes are unpacked.
The only tool required is a flat head screwdriver to screw the base pin onto the base (a very simple task). Other than that, no tools for assembly are required.
IMPORTANT - Policies and Terms/Conditions. Is due within 4 days of purchasing the listing. No order cancellations can be made once production has begun. UPS cannot deliver to P. Please open and inspect all contents immediately.All items must be new, unused, and the drapes must be unwashed. Are intended for indoor, decorative use only. They should never be used where tip-over may cause injury or damage.
Failure to use these products as intended will likely affect the safety of the products used and can result in injury or damage for which we are not responsible. The maximum weight capacity for the drape support rod is 15 pounds.
Any box that is delivered, or component piece within a box, may be sharp, and should be handled with care. Your order from us represents that you have read and agree to our.
We answer any and all questions as quickly as possible. We also sell all component pieces separately if an entire kit is not needed. The item "BA 8 FOOT TALL x 10 FOOT WIDE PIPE & BASE KIT (NO DRAPE) PIPE & DRAPE FRAME" is in sale since Tuesday, March 17, 2015. This item is in the category "Home & Garden\Wedding Supplies\Venue Decorations".
The seller is "act201" and is located in Marietta, Georgia. This item can be shipped to United States.